enrico-sorichetti
Global Moderator
Joined: 14 Mar 2007
Posts: 3277
Location: italy
|
|
|
|
what happened last thursday ?
are You referring to SNA netview/FTP ??
what is a 16/68 ???
| Quote: |
INTERNAL 08086 1434157 &SYE R= VTAM IST663I INIT OTHER REQUEST FAILED, SENSE=087D0001
INTERNAL 08086 1434157 &SYE R= VTAM IST664I REAL OLU=USIBMP0.P0EFTP05 ALIAS DLU=USIBMP0.BRIBMBJ1
INTERNAL 08086 1434157 &SYE R= VTAM IST889I SID = C3876702B7CDF1C5 |
| Quote: |
1.1.1.120 Sense Code 087D Session services path error: A session-services request cannot be rerouted along a path of SSCP-SSCP sessions. This capability is required, for example, to set up a cross-network LU-LU session.
Bytes 2 and 3 contain sense-code-specific information that indicates the specific reason for not rerouting the request.
VTAM Hint: A possible cause of this sense code is an error in the CDRM
0001 An SSCP has attempted unsuccessfully to reroute a session services request to its destination via one or more adjacent SSCPs; this value is sent by a gateway SSCP or a nongateway SSCP when it has exhausted trial-and-error rerouting.
Note: This code is used when SSCP rerouting fails completely. The remaining codes are used for failures to reroute to a particular SSCP. For example, they are associated with specific SSCPs when information about a rerouting failure is displayed in the node that was trying to reroute.
VTAM Information: When VTAM receives this sense code for a session initiation, it continues searching through the adjacent SSCP table until the destination LU is found or routing is exhausted.
VTAM Hint: Possible causes of this error include, but are not limited to, the following:
* VTAM knows which node owns the LU but is not able to route a directed search to that node to verify the availability of the LU. If messages IST894I and IST895I are issued and indicate that one of the adjacent SSCPs was ISTAPNCP with a failure sense of 087F0001, this is probably the reason for the error.
Verify that a valid search path exists. This can be CP-CP sessions and/or a subarea path. One possible cause of the problem is the absence of a CP-CP session between two nodes that share an active CP-CP capable link. If this is the case, take one of the following actions:
o Reactivate the CP-CP session.
o Deactivate the link and reactivate it as a link that is not CP-CP capable so that topology and routing services will know that it is no longer available for use in directed search routing.
* There is no SSCP-SSCP session.
* The half-session control block (HSCB) count is too low in the NCP to handle the number of sessions. A possible solution to this problem is to code a larger value on the ADDSESS keyword of the BUILD definition statement and regen.
* Both sides are using the same SSCP name.
|
| Quote: |
INTERNAL 08086 1434157 &SYE R= VTAM IST894I ADJSSCPS TRIED FAILURE SENSE ADJSSCPS TRIED FAILURE SENSE
INTERNAL 08086 1434157 &SYE R= VTAM IST895I ISTAPNCP 08400007
|
| Quote: |
IST894I ADJSSCPS TRIED FAILURE SENSE ADJSSCPS TRIED FAILURE SENSE
Explanation: VTAM issues this message as part of a subgroup of messages to provide adjacent SSCP table information in response to a DISPLAY SRCHINFO,SID command or when a session initiation fails for either of the following reasons:
* Trial and error routing using an adjacent SSCP table has failed. The destination LU was found by an SSCP, but that sscpname rejected the session initiation with sense.
* Trial and error routing using an adjacent SSCP table has exhausted the table. All adjacent SSCPs were tried, but the destination LU was not known to any of the SSCPs.
This message subgroup is displayed in a message group headed by IST663I or IST1531I. A complete description of the message subgroup follows.
IST894I ADJSSCPS TRIED FAILURE SENSE ADJSSCPS TRIED FAILURE SENSE
IST895I sscpname sense [sscpname sense]
IST894I
* This message is a header message for information displayed in IST895I.
IST895I
* This message lists the names of the adjacent SSCPs through which trial and error routing was attempted. The SSCP names appear in the order in which they were tried.
sscpname is the name of the adjacent SSCP.
o If sscpname is ISTAPNCP, this is an entry specified in the ADJSSCP table and represents a search of the APPN network. See the OS/390 IBM Communications Server: SNA Network Implementation Guide for more information.
sense is the sense code and indicates the cause of the failure. See the OS/390 IBM Communications Server: IP and SNA Codes for a description of sense.
System Action: The session setup failed.
Operator Response: Save the system log for problem determination and provide the files used for system definition.
Programmer Response: Use the output and system definition files provided to assist in determining the cause of the problem. (You may need to work with system programmers in other networks to determine the adjacent SSCP tables used in another network to define the system.) |
| Quote: |
1.1.1.63 Sense Code 0840 Procedure not valid for resource: The named RU is not supported in the receiver for this type of resource. For example, (1) SETCV specifies boundary function support for a Type 1 node, but the capability is not supported by the receiving node or (2) the NCP PU receiving an EXECTEST or TESTMODE is not the primary NCP PU for the target link.
Bytes 2 and 3 following the sense code contain sense-code-specific information.
0007 Resource not found: A DELETE or FIND could not be satisfied because the specified entry does not exist in the receiving directory.
VTAM Hint:
* VTAM cannot find a model definition to build a dynamic application program when the dynamic application program requests to open its ACB.
* VTAM cannot find a dynamic application program when the dynamic application program requests to close its ACB. |
from the messages I would say that last thursday somebody fouled up the network configuration
fouled is the politically correct term for f****d same number of letters 
but if Your support group tells that everything is OK I guess that You willh have to live with it |
|
